2. suit your application (e.g. When you do this, the upper limit range of 1000C becomes 999.9C. IM 05C01E81-01EN 1 Edition Oct. 2014 st Yokogawa Electric Corporation 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750 Japan internet site: www.yokogawa.com/ns Declaration of conformity and Manual retrieval TC10 is a panel mounting, Class II instrument. [13] AL1 and [30] AL2 will be forced to : for an absolute maximum alarm, them will be forced to the maximum input span, for an absolute minimum alarm, them will be forced to the minimum input span, for all other alarm, them will be forced to zero, [14] HAL1 and [31] HAL2 will be forced equal to the 0.5% of the input span, [35] HYS will be forced equal to 0.05 % of the input span, the CAL group will be reset [51]A.L.P, [52] A.L.O, [53] A.H.P, [54] A.H.O. Can I output in the 100% direction (20 mA or more) upon burnout? In other words the upper display will show: ]INP. There are no water or other uids (i.e. Use a tester or similar device to ensure. and workmanship for 18 months from the date of manufacturing. These two keys allow to return to the previous. IP65 rated as "dust tight" and protected against water projected from a nozzle when the optional panel gasket is mounted (for indoor locations) according to EN 60070-1. 0 mA = 0 mBar and 20 mA = -1000 mBar (vacuum). TC10-L Temperature Limit Controller - Yokogawa - Weschler Instruments Products and components that are subject to wear due to conditions. Backed by the high reliability and quality that Yokogawa has cultivated over many years. There are no water or other fluids (i.e. TC10 | Yokogawa Electric Corporation Download this manual TEMPERATURE CONTROLLER Model: TC10 - Quick Guide . We call this set conguration parameter set (or conguration parameters). Looking for more information on our people, technology and solutions? user must refer to the Engineering manual for special instructions. Safety, Protection and Modification of the Product, - In order to protect the system controlled by this product and the, product itself, and to ensure safe operation, observe the safety, precautions described in the Engineering manual. The readout is updated every 15 minutes. 1. I want to use the detailed parameter setting method of TC10, but what number is the password? Are the TC10s wiring terminals screw terminals? values and the controller output instantaneous value. Backed by the high reliability and quality that Yokogawa has cultivated over many years. All information about. The UT32A/MDL supports 920 MHz band wireless communication. All information about the controller use can be found in the Engineering Manual: - IM 05C01E81-02EN and the Communication Manual: IM 05C01E81-03EN and General Specification: GS 05C01E81-01EN. Do I need a minus sign ( - ) on the alarm setting value? Yes, if the input type is voltage or current. The UT32A-V,-C,-R is an easily configurable single-loop controller for 1/8 DIN sized. There is minimum vibrations and no impact; 4. The EU Declaration of Conformity and the manual of the controller. Related Manuals for YOKOGAWA TC10-L . Brand: YOKOGAWA . Clamp meters can perform analyses in the field on live conductors without interrupting the circuit. when you re-congure an instrument previously used for other works or from other people or when you have made too many errors during conguration and you decided to re-congure the instrument, it is possible to restore the factory conguration. Compliance: directive EMC 2004/108/CE (EN 61326-1), directive LV 2006/95/CE (EN 61010-1). The 3-year warranty extends 36 months after shipment from our factory. When the maximum front protection (IP65) is. On the TC10, I want the difference lower limit alarm to be ON 5C below the setpoint value. Search the full list . Brand: digitalview. Yokogawa TC10-L Brochure - manualmachine.com Wattmeter power consumption is the estimated hourly, energy consumption (using Load Voltage and Load Current, parameter values), computed on the previous 15 minutes. {{ baseCtrl.fullNavList[baseCtrl.fullNavList[baseCtrl.currentMenuDepth].parent].name }}, {{ baseCtrl.fullNavList[baseCtrl.currentMenuDepth].name }}, Floating Production Storage & Offloading (FPSO), Special Solutions of OpreX Transformation, Terminal Logistics Suite VP (Terminal Automation), Visual MESA Supply Chain Scheduling (VM-SCS), Cloud Inventory Management Solutions (Web*VMI), Platform for Advanced Control and Estimation (Advanced Process Control), OpreX Laboratory Information Management System, Remote Plant Performance Operation and Remote Consulting (KBC Co-Pilot Program), Mobile Field Device Management (FieldMate), Predictive Maintenance of Pump Cavitation, Advanced Analytical Instrument Management System (AMADAS), FluidCom Chemical Injection Flow Controller, Real-time Plant Data Sharing Service (Web*Technician), OpreX Data Model Broker / Design Data Validation, OpreX IT/OT Security Operations Center (SOC), Plant Information Management System (Exaquantum), Alarm Reporting and Analytics (Exaquantum/ARA), Integrated Production Information (Exaquantum/mPower), Power Performance Calculations (Exaquantum/PPC), Safety Function Monitoring (Exaquantum/SFM), Operator Trending Module (Exaquantum/OTM), Remote Data Synchronization (Exaquantum/RDS), Synchronous OPC DA Manager (Exaquantum/SDM), Manufacturing Data Exchange (Exaquantum/MDX), Public announcement of Yokogawas products, Distributed Fiber Optic Temperature Sensor, Industry and Interface Libraries (Applications and Interfaces), Yokogawa Pre-Engineered Analyzer Solutions - YES, Loading, Metering and Blending Automation, Plant Annunciator and SOE Recording System, Transmitterless SENCOMSMART Sensor Platform, Advanced Control Bioreactor System BR1000, Yokogawa announcement to Windows XP users regarding Systems products, A Business Value Decision ofImpact and Significance, Yokogawa Cloud IT/OT Connectors & Integrations, Support Information - New Legislative Framework (NLF) Conforming Products, Temperature Control for Seal-heating Parts in Wrapping Machinery. OUTLINE DIMENSIONS (mm) 1.1 INSTRUMENT DIMENSIONS 1.2 PANEL CUT-OUT 65 mm min. No. 1.Push the button for more than 3 seconds. 1. On burnout, it will be 0 mA. Worked Time counter is continuously increased when, Overall dimensions (L x H x D): 48 x 48 x 73 mm, This instrument is intended for permanent installation, for indoor. The short depth of the controller helps save instrument panel space. However, the instrument will only show the parameters applicable to its hardware options in accordance with the specic instrument conguration (i.e. Wattmeter Instantaneous power is continuously computed, as multiplication of the Load Voltage, Load Current parameter. Available: When a linear input is selected by [1] SenS. The TC10 supports easy configuration with codes for quick start-up. With thermocouple K input, can I display digits after the decimal point for the temperature? Yokogawa Supplier in Dubai UAE - InstruBiz I want to use it as a display. TC10-L is a panel mounting, Class II instrument. View online Manual for YOKOGAWA TC 10-L Controller or simply click Download button to examine the YOKOGAWA TC 10-L guidelines offline on your desktop or laptop computer. : set points, proportional band, etc.). YOKOGAWA TC10 QUICK MANUAL Pdf Download | ManualsLib 4.Pay attention to the line resistance; a high line resistance may cause measurement errors. 6. user must refer to the Engineering manual for special instructions. Before connecting the output actuators, we recommend to congure the parameters to, Yokogawa Electric Corporation - TC10-L - ENGINEERING MANUAL - PAG. 7. Can I use the DI function to switch between auto/manual and between run stop/start? The short depth of the controller helps save instrument panel space. The TC10-L features universal input, 3 Dynamic Colors Led Display two alarm outputs, retransmission output, a timer to count the total time the setpoint is exceeded, and a register to retain the maximum temperature reached. Current availability for non-stock parts is "Usually ships in 7-10 business days". The following general safety precautions must be observed during. External components (like zener barriers, etc.) Nadcap AMS2750F - What's New and How to Comply? 16 AWG or larger wires rated for at last 75C. I want to use the detailed parameter setting method of TC10, but what number is the password? I'm sending the temperature via PV transmission on TC10. The upper display will show PASS while the lower display will show 0. (24 VAC/DC), 6.0 VA max. A ladder sequence function is included as standard. NOTE: This parameter will be shown only when a TC or RTD input has been selected. YOKOGAWA TC10-L: Quick Manual| Brand: Want to have your manuals available on hand: always and everywhere? Can I turn off the "C" display with input other than temperature on TC10? For supply connections use No. Pt 1000 calibration: According to EN 60751/A2. Moreover, provide indication that the. This action allows to put the instrument in a dened condition (the same it was at the rst power ON). The TC10 supports easy configuration with codes for quick start-up. The readout is updated every 15 minutes. Please, provide a T type 1A, 250 V fuse externally. View online (36 pages) or download PDF (3 MB) YOKOGAWA TC10 User manual TC10 PDF manual download and more YOKOGAWA online manuals Case: Plastic, self-extinguishing degree: V-0 according to UL 94; Front protection: IP 65 (when the optional panel gasket is mounted) for indoor locations according to EN 60070-1; Terminals protection: IP 20 according to EN 60070-1; Terminal block: 16 screw terminals for cables of. - Installation of protection and/or safety circuits with respect to a, lightning protector; protective equipment for the system controlled, by the product and the product itself; foolproof or failsafe design, of a process or line using the system controlled by the product or, the product itself; and/or the design and installation of other, protective and safety circuits are to be appropriately implemented, Note: To leave the Configuration session without, - This product is not designed or manufactured to be used in critical, applications that directly affect or threaten human lives. use only, in an electrical panel which encloses the rear housing. 2.56 in min. Fr 8am to 5pm ET, The Yokogawa TC10-L Temperature Controller is recommended replacement. Input impedance:> 1 M. codes: Cod1 [LMNO] for the Input Type and Control Mode selection and Cod2 [PQRS] for the Alarms and the Service Functions. Yokogawa Electric Corporation - TC10 - ENGINEERING MANUAL - PAG. This is a list of recorder and controller products that support the New Legislative Framework (NLF.). The TC10-L supports easy configuration for a quick start-up, and it is configurable as a high limit or low limit controller. This manual is intended for the following personnel: - Engineers responsible for installation, wiring, and maintenance of, - Personnel responsible for normal daily operation of the equip-, Calls attention to actions or conditions that could cause serious or, fatal injury to the user or damage to the instrument, and indicates, precautions that should be taken to prevent such occurrences. With the /GK suffix, the TC10 supports the IP65. a TC J input is programmed). TEMPERATURE . condensation); The ambient temperature is in accordance with the operative temperature (0 to 50C); The relative humidity is in accordance with the instrument specications (20 to 90%); Do not run input wires together with power cables. - Installation of protection and/or safety circuits with respect to a, lightning protector; protective equipment for the system controlled, by the product and the product itself; foolproof or failsafe design, of a process or line using the system controlled by the product or, the product itself; and/or the design and installation of other, protective and safety circuits are to be appropriately implemented, - This product is not designed or manufactured to be used in critical, applications that directly affect or threaten human lives. The upper display will show PASS while the lower display shows 0; 2.Using and buttons set the value -481; 4.The instrument will turn OFF all LEDs for a few seconds, then the upper display will show dFLt (default) and then all LEDs are turned ON for 2 seconds. - Wiring should be installed to conform to NEC (National Electrical, Code: ANSI/NFPA-70) or the wiring construction standards in. 1.Do not run input wires together with power cables. WARNING! countries or regions where wiring will be installed. US $17.58. Compact size: 48 x 48 mm (1/16 DIN), depth of 48 mm + 14 mm (terminals), Universal input: (TC, mV, V, mA, Pt100-Pt1000), Easy User Control for high limit or low limit, Timer (Counts the total time the setpoint is exceeded), Register to retain the maximum temperature reached, Serial communication: RS-485 Modbus (optional), IP65 front panel (when the optional panel gasket is mounted)(optional), Universal Input: TC, mV, V, mA, Pt100, Pt1000, Power consumption: 6.0 VA max. connected between sensor and input terminals may cause errors in measurement due to excessive and/or not balanced line resistance or possible leakage currents. Also, YOKOGAWA Electric Corporation assumes no liability for the customer's, failure to comply with these requirements. Click here to select options, We're open Mo-Th 8am to 5:30pm. The instrument behaviour and its performance are governed by the value of the stored parameters. Model TC10 Temperature Controller, Quick Guide, Model TC10 Temperature Controller, Engineering Manual, Model TC10 Temperature Controller, Serial communication protocol Modbus for TC10, New Legislative Framework (NLF) Conforming Products, List of RoHS (2011/65/EU) Directive Compliant Products (6-substances RoHS compliant products), Replacement Guide for TC10 Temperature Controller, The EU Declaration of Conformity TC10 *Log-in Required, Temperature Controllers 2D CAD *Log-in Required, Compact size: 48 x 48 mm (1/16 DIN), depth of 48 mm + 14 mm (terminals), Universal input: (TC, mV, V, mA, Pt100-Pt1000), IP65 front panel (when the optional panel gasket is mounted)(optional). the protection provided by this instrument may be impaired. 18 months (a year and a half) after shipment from the factory. The TC10-L supports easy configuration for a quick start-up, and it is configurable as a high limit or low limit controller. terminal 1 and 2 to transmitter signal output. Supply Voltage: 100 to 240 VAC (-15 to +10%). Available: When a linear input is selected by [1] SenS. - This product is intended to be handled by skilled/trained person-, - This instrument is for Measurement Category No. ]inP Group - Main and auxiliary input conguration. Can I turn off the "C" display with input other than temperature on TC10? TC10 is a panel mounting, Class II instrument. The. Note: For TC and RTD inputs the decimal figure must be 0 or 1 only. On the TC10, what does it mean if AL and 1 are lit? WARNING! The EU Declaration of Conformity and the manual of the controller. "), 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750 Japan www.yokogawa.com/ns. The UT35A/UT32A also support open networks such as Ethernet communication. YOKOGAWA Accessory Manuals 12 Devices / 14 Documents Full list of YOKOGAWA Accessory Manuals YOKOGAWA AC Power Distribution Manuals 1 Devices / 1 Documents YOKOGAWA Adapter Manuals 9 Devices / 10 Documents There are no water or other fluids (i.e. YOKOGAWA TC10 Quick Manual | Manualzz Yokogawa Electric Corporation - TC10 - ENGINEERING MANUAL - PAG. Range: When the code of the input type is equal to c (see paragraph How to order). What settings should I use to output PV transmission from ananalog output terminal on TC10? A double or reinforced isolation between logic inputs and power line must be assured by the external elements. the controller use can be found in the Engineering Manual: IM 05C01E81-02EN and the Communication Manual: IM 05C01E81-03EN. Yokogawa UT55A, UT52A Manual - ManualMachine.com The equipment wholly protected by double insulation or, - Whenever a failure or a malfunction of the device may cause dan-, gerous situations for persons, things or animals, please remember, that the plant must be equipped with additional devices which, - We warrant that the products will be free from defects in material. For SSR, mA and V outputs if the line length is longer than 30 m use a shielded wire. Can you issue a TC10 calibration certificate? Such, applications include nuclear power equipment, devices using, radioactivity, railway facilities, aviation equipment, air navigation. The conguration procedure allows to take advantage of all instrument features. Can't find your region? The TC series of temperature controllers is perfect for controlling the heating temperature of sealing parts and the temperature of sealing rolls (pre-heating) in a variety of different wrapping machinery. and workmanship for 18 months from the date of manufacturing. PDF Model TC10 Temperature Controller, Engineering Manual - Instrumart Temperature drift: It is part of the global accuracy; Operating temperature: 0 to 50C (32 to 122F); Storage temperature: -20 to +70C (-4 to +158F); Yokogawa Electric Corporation - TC10-L - ENGINEERING MANUAL - PAG. Can I output in the 100% direction (20 mA or more) upon burnout? Looking for more information on our people, technology and solutions? The Yokogawa TC10 is a compact, all-in-one, single loop temperature controller with an easy-to-read, 3-color LED display. A long press allows you to close the conguration parameter procedure (the instrument will come back to the standard display). The shallow depth of the controller helps to save instrument panel space. IM 05C01E81-01EN, 2-9-32 Nakacho, Musashino-shi, Tokyo 180-8750 Japan, EU Declaration of conformity and Manual retrieval, TC10 is a panel mounting, Class II instrument. connected to the low-voltage installation. External components (like zener barriers, etc.) Use of the, instrument in a manner not prescribed herein may compromise, the product's functions and the protection features inherent in, the device. . What is the measured current of the TC10's RTD input? Cold junction accuracy: 0.04C/C after a warm-up of 20 minutes. TC10-L is a panel mounting, Class II instrument. Case: Plastic, self-extinguishing degree: V-0 according to UL 94, Front protection: IP 65 (when the optional panel gasket is mounted) for indoor locations according to EN 60070-1, Terminals protection: IP 20 according to EN 60070-1, Terminal block: 16 screw terminals for cables of 0.25 to 2.5 mm2 (AWG22 to AWG14) with connection diagram, tightening torque 0.5 Nm, Dimensions: 48 x 48, depth 62 mm (1.89 x 1.89 x 2.87 in. Calibration: According to EN 60751/A2. 0/4 to 20 mA input wiring for passive transmitter using the auxiliary pws. The Yokogawa TC10-L is an all-in-one, FM approved limit controller with an easy-to-read, 3-color LED display. . Is there a controller to which I can connect a 2-wire Pt1000 sensor? Can't find your region? -Use copper conductors only. Note: The resistance of the 3 wires must be the same.